Chamber Volume Control System Disassembly 12 N·m (1.2 kg-m, 9 Ib-ft) 22 N·m (2.2 kg-m, 16 Ib-ft) INTAKE MANIFOLD 22 N·m (2.2 kg-m, 16 Ib-ft) GASKET Replace CHAMBER VOLUME CONTROL VALVE GASKET Replace GASKET Replace CHAMBER WASHER Replace 22 N·m (2.2 kg-m, 16 Ib-ft) Attachments nsxe11123a (129 kB)
Power Seats Seat Switch Test CAUTION: Be careful not to damage the seats, the interior trim or the body. 1. Remove the two screws, then remove the power seat switch from the power seat. 2. Disconnect the 5-P connectors from each power seat switch. 3. Check for continuity between the terminals, in each switch position, […]
General Info Specifications Maintenance Engine Cooling Fuel and Emissions ’91−’92 Models ’93−’94 Models ’95−’96 Models *Transaxle Suspension *Brakes (Including ABS) *Body *Heating, Ventilation and Air Conditioning *Body Electrical *Engine Electrical *SRS 1991-96 NSX Main Menu As sections w/ * include SRS components, special precautions are required when servicing. Steering ’91−’94 Models ’95−’96 Models Attachments nsxmainidx […]
Emission Control System Three Way Catalytic Converter (cont’d) Inspection If excessive exhaust system back-pressure is suspected, remove the three way catalytic converter from the car and make a visual check for plugging, melting or cracking of the catalyst. Replace the three way catalytic converter if any of the visible area is damaged or plugged. 34 […]
Evaporative Emission (EVAP) Two Way Valve Testing 1. Remove the fuel fill cap. 2. Remove vapor line from the fuel tank and connect to T-fitting from vacuum gauge and vacuum pump as shown. VACUUM/PRESSURE GAUGE 0-4 in. Hg 07JAZ-001000 A VACUUM PUMP/ GAUGE A973X-041-XXXXX T-FITTING 3. Apply vacuum slowly and continuously while watch- ing the […]
55. Attach a chain hoist to the engine. Remove the front and rear mounting bolts, then separate the engine from the suspension and the beam assembly. CAUTION: Do not hit the engine oil cooler on the rear right beam bracket. FRONT ENGINE MOUNT REAR ENGINE MOUNT 56. Install the engine in the reverse order of […]
Disassembly NOTE: Lower the glass fully. 1. Carefully pry out the trim plate with a flat tip screwdriver as shown. CAUTION: To prevent damage to the trim plate, wrap the end of the screwdriver with a shop towel. TRIM PLATE SHOP TOWEL FLAT TIP SCREWDRIVER 2. Remove the trim plate by pulling it backward, and […]
Cylinder Heads Removal Engine removal is not required in this procedure. CAUTION: To avoid damaging the cylinder heads, wait until the engine coolant temperature drops below 100°F (38°C) before loosening the retaining bolts. NOTE: Inspect the timing belt before removing the cylinder heads. Turn the crankshaft so that the No. 1 piston is at top […]
Special Tools Ref. No. Tool Number Description KS-AHM-32-003 07JGG-001010A 07JAA-001000B 07HAZ-SG00400 07MAZ-SL00500 07MAZ-SP00500 07LAZ-SL40300 07LAZ-SL40400 07MAZ-SP0020A Digital Multimeter Belt Tension Gauge Antenna Wrench Deployment Tool Test Harness A Test Harness B Test Harness C Test Harness D Short Connector A Set Included in SRS Tool Set 07MAZ-SM5000A Included in SRS Tool Set 07MAZ-SL0010A 1 1 […]
13-42 13-42 13-39 13-40 13-39 13-42 13-42 13-39, 13-40 Special Tools Mam Menu Table of Contents Special Tools Ref. No. Tool Number Description Qty Page Reference (D O7GAJ—PG201 1o Mainshaft Holder 1 13-42 ® O7GAJ—PGZO13O Mainshaft Base 1 13-42 *® O7736—AO1000A Adjustable Bearing Puller, 25—40 mm 1 13-39 Q) 07746—0010400 Attachment, 52 X 55 mm […]