Air Mix Control Motor Replacement 1. Disconnect the heater valve cable from the air mix control motor. HEATER VALVE CABLE AIR MIX CONTROL MOTOR 2. Remove the three screws and the air mix control motor. AIR MIX CONTROL MOTOR 3. Install the air mix centrol motor in the reverse order of removal, then apply battery […]
SPRING SPECIFICATIONS Unit of length: mm (in) REGULATOR VALVE BODY LOCK BOLT 6 x 1.0 mm 12 N.m (1.2 kg-m, 9 Ib-ft) REGULATOR VALVE COOLER RELIEF VALVE REGULATOR SPRING CAP VALVE SEAT LOCK-UP CONTROL VALVE SLEEVE CAP ROLLER Regulator Valve Body Disassembly/inspection/Reassembly— Clean all parts thoroughly in solvent or carburetor cleaner, and dry with compressed […]
Wipers/Washers Windshield Wiper Motor Replacement 1. Open the hood and remove the cap nuts and the wiper arms. Don’t let the wiper arms hit the hood. 2. Remove the windshield lower molding, hood seal and air scoop by prying off the trim clips and removing the screws (see page 23-293): 3. Disconnect the 5-P connector […]
How to Read Flowcharts A flowchart is designed to be used from start to final repair. It’s like a map showing you the shortest distance. But beware: if you go off the “map” anywhere but a “stop” symbol, you can easily get lost. Describes the conditions or situation to start a troubleshooting flowchart. (bold type) […]
Dash Lights Brightness Control Component Location Index TRANSMISSION CONTROL MODULE (TCM) HEADLIGHT RETRACTOR SWITCH DASH LIGHTS BRIGHTNESS CONTROLLER Test, page 23-226 COMBINATION LIGHT SWITCH Test, page 23-STET Replacement, page 23-STET DASH LIGHTS BRIGHTNESS CONTROL UNIT Input Test, page 23-224 Attachments nsxd23216a (158 kB)
Front Sub-frame/Battery, Spare Tire Holder Sub-frame torque value specifications: 10 x 1.25 mm 60 N-m (6.0 kg-m, 43 Ib-ft) 10 x 1.25 mm 60 N-m (6.0 kg-m, 43 Ib-ft) CROSS BEAM 10 x 1.25 mm 39 N-m (3.9 kg-m, 28 Ib-ft) 12 x 1.25 mm 95 N-m (9.5 kg-m. 69 Ib-ft) 10 x 1.25 mm60 […]
Sending Unit Test Do not smoke while working on the fuel system. Keep open flame away from work area. 1. Remove the rear bulkhead panel behind the driver’s seat, then remove the access panel. 2. With the ignition switch OFF, disconnect the 3-P connector from the fuel gauge sending unit. 3. Remove the five nuts, […]
CKP/CYP Sensor Replacement NOTE: Turn the crankshaft so fhat the No. 1 piston is at top dead center (see page 6-19 (’91-’93) or (’94-’96)) 1. Remove the timing belt (see page 6-15 (’91-’93) or (’94-’96) 2. Remove the front intake end exhaust camshaft pulleys. 3. Remove the back cover. 4. Remove the CKP/CYP sensor from […]
SEALING BOLT STEEL BALLS (5/16 in) Transmission Housing Removal NOTE: Place the clutch housing on two pieces of wood thick enough to keep the mainshaft from hitting the workbench. 1. Remove the back-up light switch, neutral position switch and vehicle speed sensor (VSS). NEUTRAL POSITION SWITCH VSS (O-RING Replace .) BACK-UP LIGHT SWITCH 36 mm […]
Cruise Control Main Switch Removal CAUTION: All SRS wiring harnesses are covered with yellow outer insulation. Before disconnecting any part of the SRS wire harness, install the short connectors (see page 24-10). Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring. SRS MAIN HARNESS 1. Remove the knee […]