I Oil Seal Removal 16. Tighten the mounting bolts in a crisscross pattern in several steps. 8 x 1.0 mm SPECIAL BOLTS 40 N·m (4.0 kg-m, 29 Ib ft) 1. Remove the differential assembly. 2. Remove the oil seat from the transmission housing. OIL SEAL Replace. DIFFERENTIAL INSPECTION TOOLS 07MAJ–PR90100 BENCH VISE TRANSMISSION HOUSING 112 […]
Follow the Severe Conditions Maintenance Schedule if the car is driven MAINLY under one or more of the Severe Driving Conditions (pages 4-7:) SECTION and PAGE 8-4 (’91-’92), (’93), or (’94-’96), 8-5 8-4 (’91-92), (’93), or (’94-’96), 10-5 11-149 11-149 6-9(’94-’96), or (’91-’93) 23-96 6-15(’94-’96), or (’91-’93),10-11 23-109 11-138 (’91-92), (’93), or (’94-’96) 11-128 (’91-’92), […]
Illustrated Index Clean all parts thoroughly in solvent and dry with compressed air. Lubricate all parts with oil before reassembly. NOTE: This transmission uses no gaskets between the major housings; use liquid gasket (P/N 08718—0001). If 20 minutes have passed after applying liquid gasket, reapply it and assemble the housings and allow it to cure […]
Removal NOTE: Before removing the belt, turn the crankshaft pulley so the No. 8 piston is at top dead center (TDC) (see page 6-19 (’91-’93) or (’94-’96) Inspect the water pump after removing the timing belt (see page 10-11). If it is to be reused, mark the direction of rotation on the belt. 1. Disconnect […]
Special Tools Ref. No. Tool Number 07MAK-PR7020A Description Engine Removal/Installation Fixture Qty 1 Page Reference 5-27 Main Menu Table of Contents Special Tools Ref. No. Tool Number Description ł Qty Page Reference ® 07MAK—PR7020A Engine Removal/Installation Fixture 1 5-27 5-18 Attachments nsxd05018a (48 kB)
Foot Well Light Replacement 1. Remove the dashboard lower cover. 2. Disconnect the 2-P connector from the foot well light. DASHBOARD LOWER COVER 2-P CONNECTOR FOOT WELL LIGHT 3. Push the foot well light out of the dashboard lower cover. 4. Remove the foot well light bulb. HOUSING BULB (3.4W) LENS Ignition Key Light Replacement […]
Cable Adjustment NOTE: See page 13-6, 13-47 for removal and installation. Select Cable 1. With the transmission in neutral, measure the distance : 140.5-141.5 mm (5.53-5.57 in) 2. If distance is out of spec, loosen the locknut and turn the adjuster as necessary. ADJUSTER LOCKNUT 10 N.m (1.0 kg-m, 7 Ib-ft) 3. Tighten the locknut. […]
Fast Idle Thermo Valve Description To prevent erratic running when the engine is warming up, it is necessary to raise the idle speed. The fast idle thermo valve is controlled by a thermowax plunger. When the engine is cold, the engine coolant surround- ing the thermowax contracts the plunger, allowing ad- ditional air to be […]
Climate Control Unit Input/Output Signals CLIMATE CONTROL UNIT Main Menu Table of Contents — Climate Control Unit Input/Output Signals CLIMATE CONTROL UNIT View from wire side _I 30P: No. Wire Color Signal No. Wire Color Signal 1 GRN/BLU Air Mix control Motor [COOL €9) Output 16 RED/BLU Mode DEF Output 2 RED/VEL Mode VENT Input […]
Air Intake System Throttle Body Description The throttle body is of the single-barrel side-draft type. The lower portion of the throttle valve is heated by engine coolant which is fed from the cylinder head. The idle adjusting screw which increases/decreases bypass air and the canister/purge port are located on the top of the throttle body. […]