A/C System Service Leak Test Only use service equipment that is U.L.-listed and is cer- tified to meet the requirements of SAE J2210 to remove HFC-134a (R-134a) from the air conditioning system. CAUTION: Exposure to air conditioner refrigerant and lubricant vapor or mist can irritate eyes, nose and throat. Avoid breathing the air conditioner refrigerant […]
CLUTCH RELEASE HANGER RELEASE HANGER SPRING RELEASE BEARING GUIDE 40 x 68 x 12.5 mm OIL SEAL Replace. 10 x 20 mm DOWL PIN CLUTCH HOUSING SPEED SENSOR SENSOR DUMMY COVER O-RING Replace. HOLDER PLATE REVERSE SHIFT FORK ASSEMBLY Disassembly/Reassembly, page 13-16 REVERSE IDLE GEAR SHAFT ASSEMBLY Disassembly/Reassembly, page 13-15 OIL GUIDE RING 90 mm […]
Security Alarm System Control Unit Input Test Remove the glove box, and disconnect the 22-P connec- tor and 16-P connector from the control unit. Inspect the connector and socket terminals to be sure they are all making good contact. • If the terminals are bent, loose, or corroded, repair them as necessary, and recheck the […]
Special Tools Ref. No. Tool Number 07MAK – PR7020A 07MAZ – SL0000A Description Engine Removal/Installation Fixture NSX Fender Cover Qty 1 1 Page Reference 5-9 (’91-’93 Models) ,or (’94-’96 Models) 5-3 (’91-’93 Models) ,or (’94-’96 Models) Attachments nsxb05002a (34 kB)
Lights-on Reminder Systen. Chime Test NOTE: Refer to page 23-158 (’93-’96) (’91-’92) for a dia- gram of the lights-on reminder circuit, and page 23-166 for the input test of the circuit. When the ignition key is turned off and removed with the lights on, voltage is applied to the reminder circuit in the integrated control […]
Steering Column Removal CAUTION: All SRS electrical wiring harnesses are covered with yellow outer insulation. Before disconnecting any part of the SRS wire harness, install the short connectors (see pages 24-10(’93-’96),23-323(’91-’92) and 24-11(’93-’96), 23-323(’91-’92). Replace the entire effected SRS harness assembly if it has an open circuit or damaged wiring. 1. Disconnect both the negative […]
Troubleshooting Symptom-to-Components Chart Use this chart if the self-diagnosis checks don’t identify any cause for the symptom. Across each row in the chart, the potential sources of a symptom are ranked in the order they should be inspected in, starting with . Find the symptom in the left column, read across to the most likely […]
Wheel Alignment Height NSX/NSX-T four wheel alignment requires the use of equipment designed specifically for four wheel independent suspensions and capable of immediate feedback. NOTE: For proper inspection/adjustment of the wheel alignment, check and adjust the following before checking the alignment. • Check that the suspension is not modified. • Check the tire size and […]
Alternator Belt Adjustment Deflection Method: 1. Apply a force of 100 N (10kg, 22 Ibs) between the alternator and crankshaft pulley, and measure its deflection. Deflection: 11-13.5 mm (0.43-0.53 in) NOTE: On a brand-new belt, the deflection should be 6-8 mm (0.24-0.31 in) before the belt has had any running time on the engine. ADJUSTING […]
Throttle Body (cont’d) Disassembly THROTTLE CABLE 22 N·m (2.2 kg-m, 16lb-ft) CAUTION: THROTTLE VALVE DASHPOT TP SENSORCONTROL DIAPHRAGM Testing, page 11-135 IDLE ADJUSTING SCREW O-RING Replace The throttle stop screw is non-adjustable. After reassembly, adjust the throttle cable (see page 11-130). After replacement, adjust the idle speed (see page 11-102). Attachments nsxd11133a (196 kB)