Rocker Arms and Shafts Clearance Measure both the intake rocker shafts and exhaust rocker shafts. 1. Measure diameter of shaft at first rocker location. MICROMETER Surface should be smooth. 2. Zero gauge to shaft diameter. MICROMETER CYLINDER BORE GAUGE Inspect rocker arm face for wear. Repeat for all rockers. 3. Measure inside diameter of rocker […]
Piston/Connecting Rod Assemblies Inspection 1. Check the piston for distortion or cracks. NOTE: If cylinder is bored, an oversized piston must be used. 2. Measure piston diameter at a point 17 mm (0.67 in) from the bottom of the skirt. NOTE: There are two standard-size pistons (A = no letter and B). The letter is […]
BRACKET BEAM COTTER PIN Replace. SELECT LEVER PIN SELECT LEVER MOUNTING BOLT SHIFT CABLE HOLDER 6 x 1.0 mm 12 N.m (1.2 kg-m, 9 Ib-ft) 6 x 1.0 mm 8 N.m (0.8 kg-m, 6 Ib-ft) SHIFT CABLE CLAMPS SHIFT CABLE COVERLOCK PINInstall in this direction. CONTROL LEVER LEVER CONTROL SRS MAIN HARNESS Make sure lifts […]
Knuckle/Control Arms Illustrated Index Overall Suspension NOTE: • Wipe off the grease before tightening the nut at the ball joint. • Torque specifications, see page 18-30. • Align the white line on the stabilizer bar with the bushing end, and install the stabilizer bar. Corrosion resistant bolt/nut REAR DAMPER STABILIZER BAR BRACKET Check for damage. […]
Roof Holder Switch Test 1. Open the rear hatch and engine cover. 2. Disconnect the 1- P connector from the roof holder switch. 3. There should be continuity between the A and B ter- minals with the switch released (roof not stored). 4. There should be no continuity with the switch pushed (roof stored). Roof […]
Combination Light/Turn Signal Switch Test 1. Remove the dashboard lower cover (see page 23-182). 2. Disconnect the 18-P connector from the floor wire harness. 3. Check for continuity between the terminals, in each switch position, according to the table. 18-P CONNECTOR View from wire side Turn Signal Switch Headlight/Dimmer/Passing Switch Attachments nsxb23181a (47 kB)
Fuel Supply System System Troubleshooting Guide NOTE: Across each row in the chart, the systems that could be sources of a symptom are ranked in the order they should be inspected starting with . Find the symptom in the left column, read across to the most likely source, then refer to the page listed at […]
Component Locations GAUGE ASSEMBLY UNDER-HOOD FUSE/ RELAY BOX TRANSMISSION CONTROL MODULE (TCM) 22P CONNECTOR VEHICLE SPEED SENSOR (VSS) (M/T) PULSE UNIT 7P CONNECTOR TORQUE SENSOR 6P CONNECTOR/ ROTATION SENSOR 4P CONNECTOR STEERING GEARBOX (TORQUE SENSOR/ ROTATION SENSOR) UNDER-DASH FUSE BOX EPS CONTROL UNIT ALTERNATOR 4P CONNECTOR GAUGE ASSEMBLY EPS INDICATOR LIGHT UNDER-HOOD FUSE/RELAY BOX No. […]
Thermostat Replacement NOTE: Use new gaskets and O-rings when reassem- bling. ENGINE COOLANT TEMPERATURE (ECT) GAUGE SENDING UNIT 9 N-m (0.9 kg-m, 7 Ib-ft) Apply liquid gasket to the threads. WATER PASSAGE 8 x 1.25 mm 22 N-m (2.2 kg-m, 16 Ib-ft) BLEED BOLT 10 N-m (1.0 kg-m, 7 Ib-ft) 6 x 1.0 mm 12 […]
Modulator/Solenoid Unit Solenoid Leak Test 1. Disconnect the 6-P inspection connector (PNK) from the connector cover located under the glove box, and connect the 6-P inspection connector to the ALB checker. CONNECTOR COVER ALB CHECKER 07HAJ-SG0010B See page 19-2 for other applicable checkers. 6-P INSPECTION CONNECTOR CAUTION: Place the vehicle on level ground with the […]