Air Cleaner (ACL) ACL Element Replacement ACL HOUSING COVER ACL ELEMENT Normal conditions: Replace air cleaner element every 30,000 miles (48,000 km) or 24 months whichever comes first. Severe conditions: Clean air cleaner element every 15,000 miles (24,000 km) or 12 months and replace every 30,000 miles (48,000 km) or 24 months whichever comes first. […]
Cooling Cooling System Two cooling systems are employed: An antifreeze/water system with the radiator mounted in the front of the vehicle. An air-cooling system driven by a fan mounted in the engine compartment. BLEEDER RADIATOR BLEEDER WATER VALVE HEATER CORE DRAIN DRAINS BLEEDER ENGINE DRAIN WATER PUMP ENGINE OIL COOLER ENGINE DRAIN FAST IDLE THERMO […]
Power Door Locks Driver’s Door Actuator Test 1. Remove the door panel (see section 20). 2. Disconnect the 8-P connector from the actuator. ACTUATOR View from wide side 3. Test actuator operation: LOCK: With battery power connected to the No. 7 terminal, connect ground to the No. 8 terminal momentarily. UNLOCK: With battery power connected […]
Rear Roof Stop Guide Replacement CAUTION: To prevent damage, place the roof on an appropriate pad. 1. Remove the roof. 2. Remove: • Roof front trim (see page 20-82) • Roof side trim (see page 20-82) • Roof side lock (see page 20-83) • Rear roof lock guide (see page 20-90) 3. Remove the rear […]
SRS components are located in this area. Review the SRS component locations, precautions, and procedures in the SRS section 24 before performing repairs or service. POWER TRANSISTOR BLOWER MOTOR RECIRCULATION CONTROL MOTOR CONDENSER FAN MOTOR UNDER-HOOD RELAY BOX A (CONDENSER FAN RELAY, COMPRESSOR CLUTCH RELAY, BLOWER MOTOR HIGH RELAY, BLOWER MOTOR RELAY) UNDER-HOOD FUSE/RELAY BOX […]
Special Tools Ref. No. Tool Number 07GAF-SD40700 07MAC-SL00200 07MAG-SL00100 07MAJ-SLOOOOA 07MAZ-SL00100 07MAZ-SL00200 07MAZ-SL00300 07MAZ-SL00400 07908-ME90000 07916-SA50001 07973-6920001 07974-SD90000 Description Hub Dis/Assembly Base Ball Joint Remover, 28 mm Ball Joint Boot Clip Guide EPS Test Set Test Harness A Test Harness B Test Harness C Power Unit Checker Locknut Wrench Locknut Wrench, 40 mm P/S Adjustment […]
Rear Damper Installation 1. Reposition the damper assembly between the frame and knuckle. 2. Install the stabilizer link and connect the stabilizer bar. 3. Loosely install a new self-locking nut. 4. Hold the ball pin of the stabilizer link with a hex wrench, then tighten the self-locking nut. 5. Loosely install a new damper mounting […]
Illustrated Index Left Side Cover Main Menu Table of Contents Illustrated Index Left Side Cover 14-100 LEFT SIDE COVER DOWEL PIN GASKET Replace. SEALING WASHER Replace. O-RING Replace. 1ST-HOLD CLUTCH FEED PIPE O-RING Replace. FEED PIPE FLANGE SNAP RING 1ST CLUTCH FEED PIPE O-RING Replace. FEED PIPE FLANGE SNAP RING CONICAL SPRING WASHER Replace. BALL […]
Intake Air System Inspection/Adjustment 1. Warm up the engine to normal operating tem- perature (the cooling fan comes on). 2. Check that the throttle cable operates smoothly with no binding or sticking. Repair as necessary. 3. Check cable free play at the throttle linkage. Cable deflection should be 10—12 mm (0.39—0.47 in.). Installation 1. Fully […]
System Description System Connectors [Behind the bulkhead panels] Main Menu Table of Contents System Description System Connectors [Behind the bulkhead panels] icont’d) C483 c482 c135 (ECM-A) C144 C136 (BOMB) C137 (ECM-C) C1 38 (ECM-DI ENGINE WIRE HARNESS C141 ì i C481 c140 c479 Í C139 j I C480 /1 у / FLOOR WIRE HARNESS 11-28 […]