Design Specifications Main Menu Table of Contents Design Specifications ITEM METRIC ENGLISH NOTES Dimensions Overall Length 4,425 mm 174.2 in Overall Width 1,810 mm 71.3 in Overall Height 1,175 mm 46.3 in Wheelbase 2,530 тт 99.6 in Track F/R 1,510/1,530 mm 59.4/60.2 in Ground Clearance 135 mm 5.3 in Seating Capacity 2 Weight (USA) Gross […]
Safety Indicator (NSX-T “open top”) Roof Lock Switch Test 1. Remove the headliner (see section 20). 2. Disconnect the 3-P connector from the roof lock switch. ROOF LOCK SWITCH View from wire side 3. There should be continuity between the A and B ter- minals with the switch released (roof unlatched or off). 4. There […]
Synchro Sleeve, Synchro Hub Inspection 1. Inspect gear teeth on all synchro hubs and synchro sleeves for rounded off corners, which indicates wear. 2. Install each synchro hub in its mating synchro sleeve, and check for freedom of movement. NOTE: If replacement is required, always replace the synchro sleeve and synchro hub as a set. […]
Air Intake System Chamber Volume Control Valve Test CAUTION: Do not adjust the chamber volume control valve full-close screw. It was preset at the factory. 1. Check the chamber volume control valve shaft for binding or sticking. 2. Check the chamber volume control valve for smooth movement. 3. Check that A of the chamber volume […]
Side Marker/Turn Signal/Hazard Flasher System Description To cope with dimensional requirements for the airbag components and to offer better operational feel, the turn signal lever and the cancel mechanism are separated mechanically, and connected electrically instead. The system cancels the turn signals electrically, by means of a solenoid, after a turn is made. A sensor […]
Evaporative Emission Controls Description The evaporative controls are designed to minimize the amount of fuel vapor escaping to the atmosphere. The system consists of the following components: A. Charcoal Canister A canister for the temporary storage of fuel vapor until the fuel vapor can be purged from the canister into the engine and burned. B. […]
Throttle Cable Inspection/Adjustment 1. Warm up the engine to normal operating tem- perature (cooling fan comes on). 2. Check that the throttle cable operates smoothly with no binding or sticking. Repair as necessary. 3. Check cable free play at the throttle linkage. Cable deflection should be 10-12 mm (0.39-0.47 in.) Installation 1. Fully open the […]
Seat Belts Replacement CAUTION: Check the seat belts for damage and replace them if necessary. Be careful not to damage them durinc removal and installation. NOTE: Remove the anchor bolts with a 1 7 mm socket or box-end wrench. 1. To remove the seat belts, first remove the seats (page 20-38). NOTE: Take care not […]
(’93-’96), 86 (’91-’92 Models) MODE CONTROL MOTOR Replacement, page 22-57 (’93-’96), 69 (’91-’92 Models) Test, page 22-58 (’93-’96), 91 (’91-’92 Models) “DEF” DOOR Adjustment, page 22-77 (’92-’96), 72 (’91Models) “HEAT” DOOR Adjustment, page 22-77 (’92-’96), 72 (’91Models) RECIRCULATION CONTROL MOTOR Replacement, page 22-59 (’93-’96), 64 (’91-’92) Test, page 22-59 (’93-’96), 64 (’91-’92 Models)BLOWER UNIT Replacement, […]
Installation NOTE: Before installing the steering wheel, make sure the front wheels are straight ahead. CAUTION: • Be sure to install the harness wires so that they are not pinched or interfering with other car parts. • Do not replace the original steering wheel with any other design, since it will make it impossible to […]