Cruise Control Control Unit Input Test CAUTION: AH SRS wiring harnesses are covered with yellow outer Insulation. Before disconnecting any part of the SRS wire harness, install the short connectors (see page 24-10). Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring. Remove the glove box, then disconnect […]
Noise Condenser Capacity Test 1. Use a commercially available condenser tester. Con- nect the tester probes and measure the condenser capacity. Condenser capacity: 0.47 ± 0.09 microfarads POSITIVE TERMINAL BODY GROUND (Negative) NOTE: The noise condenser is intended to reduce ignition noise. However, condenser failure may cause the engine to stop running. 2. If not […]
A/T Gear Position Indicator Component Location Index SRS components are located in this area. Review the SRS component locations, precautions, and procedures in the SRS section 24 before performing repairs or ser- vice. NOTE: For indicator troubleshooting, refer to sec- tion 14. A/T GEAR POSITION INDICATOR Input Test, page 23-158 TRANSMISSION CONTROL MODULE (TCM) See […]
Special Tools Ref. No. Tool Number 07HAH—-PJ7010B 07JAA—001020A 07JAB—001020A 07MAA—PR70110 07MAA—PR70120 07MAF—PR9010A 07MAJ—PR7020A 07NAB—001030A 07NAB — 001040A 07742—0010100 07757—-PJ1010A Description Valve Guide Reamer, 5.5 mm Socket, 19 mm Holder Handle Tappet Adjuster Tappet Locknut Wrench Valve Spring Compressor Attachment Extension VTEC Plug Holder Attachment, 45 mm Holder Attachment, 50 mm Valve Guide Driver, 5.5 mm […]
Illustrated Index Transmission Housing Table of Contents Main Menu Illustrated Index Transmission Housing 14-102 SNAP RING WASHER THRUST NEEDLE BEARING MAINSHAFT 4TH GEAR NEEDLE BEARINGS MAINSHAFT 4TH GEAR COLLAR THRUST NEEDLE BEARING THRUST WASHER 4TH CLUTCH ASSEMBLY O-RING Replace. MAINSHAFT SEALING RING 37 mm NEEDLE BEARING SET RING REVERSE SHIFT FORK LOCK WASHER Replace. COUNTERSHAFT […]
Interlock System Shift Lock Solenoid Test/Replacement Test: 1. Remove the console, then disconnect the 3-P con- nector of the shift lock solenoid from the floor wire harness. NOTE: This solenoid has a diode in it. To get an accurate reading, either test it with a volt-ohmmeter that compensates for diodes, or make sure you con- […]
A/T Gear Position Indicator Indicator Input Test SRS components are located in this area. Review the SRS component locations, precautions, and procedures in the SRS section (24) before performing repairs or ser- vice. Remove the dashboard lower cover, dashboard lower pad and instrument panel. Disconnect the connector “A” 130-P) from the gauge assembly (see page […]
M/T: Manual Transmission A / T : Automatic Transmission Cooling — Section 10 Engine Lubrication — Section 8 Engine Block — Section 7 Main Menu Table of Contents ÿ Engine Block — Section 7 – ¡Unit of length: mm (in) MEASUREMENT STANDARD (NEW) SERVICE LIMIT Cylinder block Warpage of deck surface 0.07 (0.003) maxî‘k O. […]
Valves, Valve Springs and Valve Seals Valve Spring and Valve Seal Installation Sequence NOTE: Exhaust and intake valve seals are NOT interchangeable. INTAKE VALVE SPRING NOTE: Place the end of valve spring with closely wound coils toward the cylinder head. INTAKE VALVE SEAL (WHITE SPRING) Replace. VALVE SEAL INSTALLER KD-2899 VALVE SEAL Replace. VALVE KEEPERS […]
Combination Light /Turn Signal Switch Test 16-P CONNECTOR 1. Remove the dashboard lower cover and knee bolster pad. 2. If necessary, remove the knee bolster. 3. Disconnect the 16-P connector from the floor wire harness. 4. Check for continuity between the terminals, in each switch position according to the table. View from wire side Turn […]