Identification Number Locations VEHICLE IDENTIFICATION NUMBER VEHICLE IDENTIFICATION NUMBER MANUAL TRANSMISSION NUMBER AUTOMATIC TRANSMISSION NUMBER ENGINE NUMBER Attachments nsxa01004a (62 kB)
Categories
nsxa01004a.pdf
Month: August 2017
Categories
nsxb19026a.pdf
Brake Hoses/Pipes Inspection 1. Inspect the brake hoses for damage, deterioration, leaks, interference or twisting. 2. Check the brake lines for damage, rusting and leakage. Also check for bent brake lines. 3. Check for leaks at hose and line joints or connections, and retighten if necessary. CAUTION: Replace the brake hose clip whenever the brake […]
Categories
nsxb04002a.pdf
Lubrication Points For the details of lubrication points and types of lubricants to be applied, refer to the Illustrated Index and various work procedures (such as Assembly/Reassembly, Replacement, Overhaul, Installation, etc.) contained in each section. Main Menu Table of Contents CD za (1’3‘ fl” © z) Ш 2 ® 24 Attachments nsxb04002a (83 kB)
Categories
nsxb11130a.pdf
Fuel Supply System Fuel Lines NOTE: Check all fuel system lines and hoses for damage, leaks or deterioration, and replace if necessary. 27 N-m (2.8 kgf-m, 21 Ibf-ft) 27 N-m (2.8 kgf-m, 21 Ibf-ft) 27 N-m (2.8 kgf-m, 21 Ibf-ft) 22 N-m (2.2 kgf-m, 16 Ibf-ft) NOTE: Check all hose clamps and retighten if necessary. […]
Categories
nsxb06012a.pdf
Crankshaft Pulley and Pulley Bolt Replacement When installing and tightening the pulley, follow the procedure below. Clean, remove any oil and lubricate points shown below. Clean Remove any oil Lubricate CRANKSHAFT PULLEY WASHER PULLEY BOLT TIMING BELT DRIVE PULLEY CRANKSHAFT TIMING BELT GUIDE PLATE TIMING BELT GUIDE PLATE Crankshaft pulley bolt size and torque value: […]
Categories
nsxe11106a.pdf
Fuel Supply System Fuel Pump Resistor Troubleshooting Flowchart Engine will not start. Inspection of fuel pump resistor. Disconnect the fuel pump resis- tor connector. Measure the voltage between BLK/YEL (+) (on harness side) and body ground (-) when the ig- nition switch is first turned ON. Is there battery voltage? (for 2 seconds) Inspect the […]
Categories
nsxd11131b.pdf
Throttle Body Description The throttle body is of the single-barrel side-draft type. The lower portion of the throttle valve is heated by engine coolant which is fed from the cylinder head. The idle adjusting screw which increases/decreases bypass air and the evaporative emission (EVAP) control canister port are located on the top of the throttle […]
Categories
nsxd17073a.pdf
Power Unit Replacement 1. Remove the floor mat and speaker cover. 2. Disconnect the connector from the speaker and re- move the speaker by removing the bolt and nut. SPEAKER COVER 5. Remove the power unit by disconnecting the con- nector. 10 N.m (1.0 kg-m, 7 lb-ft) 3. Remove the power unit bracket. 4. Bend […]
Categories
nsxd06027a.pdf
Crankshaft Position (CKP)/Cylinder Position (CYP) Sensor NOTE: Turn the crankshaft so that the No. 1 piston is at top dead center (page 6-25, 26). 1. Remove the timing belt (page 6-23, 24). 2. Remove the front intake and exhaust camshaft pulleys. 3. Remove the front timing belt cover plate. 4. Remove the CKP/CYP sensor from […]
Categories
nsxd17068a.pdf
Power Steering Illustrated Index CAUTION: Do not try to disassemble the power steering gearbox. If the gearbox is faulty, replace it as an assembly. Corrosion resistant bolt/nut GEARBOX ASSEMBLY MOUNT BASE 10 mm FLANGE NUT 60 N·m (6.0 kg-m, 43 Ib-ft) FLANGE BOLT 10 N.m (1.0 kg-m, 7 Ib-ft) GROUND CABLE STOP WASHER LOCK WASHER […]