Category: Brakes & ABS

Wheel Sensor Signal Confirmation NOTE: Use the ALB checker (mode 0) to confirm pro- per wheel sensor operation. 1. Disconnect the 6-P inspection connector from the connector cover located under the glove box, and connect the 6-P inspection connector to the ALB checker. 07HAJ-SG0010B see page 19-2 for other applicable checkers. 2. Raise the car […]

Hydraulic System Relieving Accumulator/Line Pressure Use the Bleeder T-Wrench before disassembling the parts shaded in the illustration. 1. Drain the brake fluid from the master cylinder and modulator reservoir thoroughly. 2. Remove the red cap from the bleeder on the top of the power unit. 3. Install the special tool on the bleeder screw and […]

Brake Hoses/Pipes Inspection 1. Inspect the brake hoses for damage, deterioration, leaks, interference or twisting. 2. Check the brake lines for damage, rusting and leakage. Also check for bent brake lines. 3. Check for leaks at hose and line joints or connections, and retighten if necessary. CAUTION: Replace the brake hose clip whenever the brake […]

Special Tools Ref. No. Tool Number 07HAA – SG00100 or 07HAA – SG00101 07HAE – SG00100 07HAJ – SG00100or 07HAJ – SG0010B 07JAG – SD40100 07KA2 – 001000A 07914 – SA50000 Description Bleeder T-Wrench Brake Spring Compressor ALB Checker (US) Pushrod Adjustment Gauge Auxiliary Window Switch Snap Ring Pliers Qty 1 1 1 1 1 […]

There should be continuity between the A and B termi- nals when the battery is connected to the C and D ter- minals. There should be no continuity between the A and B ter- minals when the battery is disconnected. Fail-Safe Relay Test Electronic Components TCS Switch Test There should be continuity between the D […]

Troubleshooting TCS Indicator Light Temporary Driving Conditions: 1. The TCS indicator light will come on and the control unit memorizes the Diagnostic Trouble Code (DTC) under cer- tain temporary conditions: 2. If the TCS indicator light does not come back on after correcting the tire or tire pressure problem, the TCS system is OK. NOTE: […]

Solenoid Flushing 1. Remove the motor relay from the under-hood fuse/relay box. (Location: page 19 – 40) 2. Install the auxiliary window switch (07KAZ — 001000A) into the two motor relay cavities in the relay box. MOTOR RELAYWINDOW SWITCH 07KAZ-001000A UNDER-HOOD FUSE/RELAY BOX 3. Disconnect the four modulator solenoid connec- tors. 4. Bleed any high-pressure […]

Wiring/Connector Location Mam Menu Table of Contents Wiring/Connector Location ,— FRONT FAIL-SAFE RELAY REAR FAIL-SAFE RELAY INSPECTION CONNECTOR SERVICE CHECK CONNECTOR RIGHT-FRONT SENSOR CONNECTOR ABS PARKING BRAKE SWITCH CONNECTOR LEFT—FRONT SENSOR CONNECTOR PRESSURE SWITCH CONNECTOR RIGHT-FRONT SOLENOID CONNECTOR LEFT-FRONT SOLENOID CONNECTOR RIGHT-REAR SOLENOID CONNECTOR LEFTvREAR SOLENOID CONNECTOR PUMP MOTOR CONNECTOR RIGHT-REAR SENSOR CONNECTOR LEFT-REAR SENSOR […]

Bleeding Air Bleeding with ALB Checker 1. Disconnect the 6-P inspection connecotor (PNK) from the connector cover located under the glove box and connect the inspection connector to the ALB checker. ANTI-LOCK BRAKE SYSTEM INDICATOR LIGHT CONNECTOR COVER ALB CHECKER 07HAJ – SG00100 or 07HAJ – SG0010B (US) or 07HAJ-SG00200 (Canada) 6-P INSPECTION CONNECTOR CAUTION: […]

Anti-lock Brake System (ABS) Description Features/Construction/Operation General In a conventional brake system, if the brake pedal is depressed excessively, the wheels can lock before the vehicle comes to a stop. In such a case, the stability of the vehicle is reduced if the rear wheels are locked, and maneuverabily of the vehicle is reduced if […]