Category: Electrical
nsxb23306a.pdf
![](https://beta.nsxshop.com/wp-content/uploads/2017/08/4f8ce942ed126cbb8da41663247ea08b39253fc3292e05016e08e8323cf509f0.jpg)
Cruise Control Main Switch Test 1. Remove the dashboard lower cover (see page 23-305). 2. If necessary, remove the dashboard lower pad. 3. Disconnect the 20-P connector, and check for conti- nuity between the terminals, in each switch posi- tion, according to the table. CRUISE CONTROL SWITCH 20-P CONNECTOR View from wire side Attachments nsxb23306a […]
nsxf23088a.pdf
![](https://beta.nsxshop.com/wp-content/uploads/2017/08/cec535951b29a862d68b1124660dd612cd01e1a6984a2b2802e61ecf5e7a1394.jpg)
Ignition system Component Location Index IGNITION TIMING CONTROL SYSTEM Troubleshooting, section 11 Inspection and setting, page 23-91 Description, page 23-89 RADIO NOISE CONDENSER Test, page 23-97 SPARK PLUGS (6) Inspection, page 23-96 TACHOMETER CONNECTOR (Engine revolution detected) CYL/CRANK SENSOR Troubleshooting, section 11 Replacement, section 5 IGNITION COILS (6) Removal, page 23-94 Test, page 23-95 IGNITER […]
nsxe23234a.pdf
![](https://beta.nsxshop.com/wp-content/uploads/2017/08/1fadaff193842e214a24d487990763752616ff4bb508b851130f4ac2f184f25b.jpg)
Stereo Sound System Rear Speaker Replacement 1. Remove the center armrest and upper bulkhead panel (see section 20). 2. Remove the bulkhead panels. 3. Remove the 5 screws, then disconnect the 2-P con- nector from the floor wire harness. CENTER BULKHEAD PANEL R. BULKHEAD PANEL 2-P CONNECTOR L. BULKHEAD PANEL 4. Remove the 4 screws, […]
nsxb23326a.pdf
![](https://beta.nsxshop.com/wp-content/uploads/2017/08/13324746d1127731de3f9dbd5eabe93252d55c6bb1e5d2836a77bc99a4a85f68.jpg)
Security Alarm System Ignition Key Switch Test SRS components are located in this area. Review the SRS component locations, precautions, and procedures in the SRS section 24 before performing repairs or ser- vice. 1. Remove the dashboard lower cover, and disconnect the connectors. DASHBOARD LOWER COVER 2. Disconnect the 8-P connector from the floor wire […]
nsxd23286b.pdf
![](https://beta.nsxshop.com/wp-content/uploads/2017/08/7702334a993eea4cf3bd0c4c04419669f374ce18c6e72227f51195a99edf04ee.jpg)
Wipers/Washers Windshield Wiper Motor Replacement 1. Open the hood and remove the cap nuts and the wiper arms. Don’t let the wiper arms hit the hood. 2. Remove the windshield lower molding, hood seal and air scoop by prying off the trim clips and removing the screws (see page 23-293): 3. Disconnect the 5-P connector […]
nsxd23216a.pdf
![](https://beta.nsxshop.com/wp-content/uploads/2017/08/84c3c06d6903d312c05412c1936318cc8278ee4372d820ab9032766c024aaa6f.jpg)
Dash Lights Brightness Control Component Location Index TRANSMISSION CONTROL MODULE (TCM) HEADLIGHT RETRACTOR SWITCH DASH LIGHTS BRIGHTNESS CONTROLLER Test, page 23-226 COMBINATION LIGHT SWITCH Test, page 23-STET Replacement, page 23-STET DASH LIGHTS BRIGHTNESS CONTROL UNIT Input Test, page 23-224 Attachments nsxd23216a (158 kB)
nsxb23135a.pdf
![](https://beta.nsxshop.com/wp-content/uploads/2017/08/067026de27da9ebc5a6476b1cf9efc8213c2616c5824044bbca992eb43b639ea.jpg)
Sending Unit Test Do not smoke while working on the fuel system. Keep open flame away from work area. 1. Remove the rear bulkhead panel behind the driver’s seat, then remove the access panel. 2. With the ignition switch OFF, disconnect the 3-P connector from the fuel gauge sending unit. 3. Remove the five nuts, […]
nsxd23298a.pdf
![](https://beta.nsxshop.com/wp-content/uploads/2017/08/bf7cfa7a73f40497d5833afd72a7b018e75a1e9cd9dfbd399ebfefc3c71d0ebe.jpg)
Cruise Control Main Switch Removal CAUTION: All SRS wiring harnesses are covered with yellow outer insulation. Before disconnecting any part of the SRS wire harness, install the short connectors (see page 24-10). Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring. SRS MAIN HARNESS 1. Remove the knee […]
nsxb23277a.pdf
![](https://beta.nsxshop.com/wp-content/uploads/2017/08/1c5439b9c44fb4f4acde8802b38fbf7a9253634fffea4960086ab46d2cff8d68.jpg)
Relay Test 1. Remove the power window relay in the under-hood fuse/relay box. 2. Check continuity at the relay terminals. • There should be continuity between the C and D terminals. • There should be continuity between the A and B terminals when power and ground are connect- ed to the C and D terminals. […]
nsxb23117a.pdf
![](https://beta.nsxshop.com/wp-content/uploads/2017/08/34c8c64fa2682f2c19225ac1aa4262f9f3ea7479dbea528663fa30175a881089.jpg)
Radiator Fan Motor Test 1. Disconnect the 2-P connector from the radiator fan motor. 2. Test the motor by connecting battery power to the A terminal, and ground to the B terminal. 3. If the motor fails to run or does not run smoothly, replace it. Condenser Fan Motor Test 1. Disconnect the 2-P connector […]