Remove any oil.
TIMING BELT
Inspection, page 6-22
Adjustment, page 6-22
6 x 1.0 mm
12N.m(1.2kg-m,9 Ib-ft)
Timing Belt
Illustrated Index
Turn the crankshaft so that the No. 1 piston is at top
dead center (TDC) (page 6-25, 26)
Replace rubber seals if damaged or deteriorated.
Prior to installing the cylinder head cover, apply a thin
layer of liquid gasket to the mating surface of the
cylinder head cover and rubber seals to prevent the
rubber seal from falling of.
CYLINDER HEAD COVER
CAP NUT
6x 1.0 mm
10N.m (1.0 kg-m, 7 Ib-ft)
CAP NUT
6 x 1.0 mm
10N.m (1.0 kg-m,
7 Ib-ft)
WASHER
RUBBER SEALS
Replace when damaged
or deteriorated.
ADJUSTING BOLT
10 x 1.25 mm
43N.m (4.3 kg-m,31 Ib-ft)
For adjustment only,
do not remove.
Remove any oil.
COLLARS
RUBBER SEALS
Replace when damaged
or deteriorated.
6 x 1.0 mm
12N.m (1.2 kg-m.
9 Ib-ft)
6×1.0 mm
12N.m (1.2 kg-m.
9 Ib-ft)
TIMING BELT
FRONT MIDDLE
COVER
CRANKSHAFT
PULLEY
Remove any oil.
6 x 1.0 mm
12N.m (1.2 kg-m.
9 Ib-ft)
SPECIAL BOLT
16 x 1.5 mm
250N.m (2.5 kg-m,
181 Ib-ft)
Tightening torque for
a new crankshaft.
Apply oil to the bolt threads,
but not to the surface
that contacts the washer.
280 0 250N.m
28 0 25 kg-m.
203 0 181 Ib-ft
LOWER COVER
RUBBER SEAL
After installation, fill the engine with oil up to the
specified level, run the engine for more than 3
minutes, then check for oil leakage.
When installing a new crankshaft;
i tighten the crankshaft pulley bolt to 280N.m (28
kg-m, 203 Ib-ft), loosen it, retighten it to 250
N.m (25 kg-m, 181 Ib-ft).
TIMING BELT
Inspection, page 6-22
Adjustment, page 6-22
6 x 1.0 mm
12N.m(1.2kg-m,9 Ib-ft)
Timing Belt
Illustrated Index
Turn the crankshaft so that the No. 1 piston is at top
dead center (TDC) (page 6-25, 26)
Replace rubber seals if damaged or deteriorated.
Prior to installing the cylinder head cover, apply a thin
layer of liquid gasket to the mating surface of the
cylinder head cover and rubber seals to prevent the
rubber seal from falling of.
CYLINDER HEAD COVER
CAP NUT
6x 1.0 mm
10N.m (1.0 kg-m, 7 Ib-ft)
CAP NUT
6 x 1.0 mm
10N.m (1.0 kg-m,
7 Ib-ft)
WASHER
RUBBER SEALS
Replace when damaged
or deteriorated.
ADJUSTING BOLT
10 x 1.25 mm
43N.m (4.3 kg-m,31 Ib-ft)
For adjustment only,
do not remove.
Remove any oil.
COLLARS
RUBBER SEALS
Replace when damaged
or deteriorated.
6 x 1.0 mm
12N.m (1.2 kg-m.
9 Ib-ft)
6×1.0 mm
12N.m (1.2 kg-m.
9 Ib-ft)
TIMING BELT
FRONT MIDDLE
COVER
CRANKSHAFT
PULLEY
Remove any oil.
6 x 1.0 mm
12N.m (1.2 kg-m.
9 Ib-ft)
SPECIAL BOLT
16 x 1.5 mm
250N.m (2.5 kg-m,
181 Ib-ft)
Tightening torque for
a new crankshaft.
Apply oil to the bolt threads,
but not to the surface
that contacts the washer.
280 0 250N.m
28 0 25 kg-m.
203 0 181 Ib-ft
LOWER COVER
RUBBER SEAL
After installation, fill the engine with oil up to the
specified level, run the engine for more than 3
minutes, then check for oil leakage.
When installing a new crankshaft;
i tighten the crankshaft pulley bolt to 280N.m (28
kg-m, 203 Ib-ft), loosen it, retighten it to 250
N.m (25 kg-m, 181 Ib-ft).