Category: Automatic Transmission

Component Location LOCK-UP CONTROL SOLENOID VALVE ASSEMBLY MAINSHAFT SPEED SENSOR FRONT SHIFT CONTROL SOLENOID VALVE ASSEMBLY ENGINE COOLANT TEMPERATURE (ECT) SENSOR Engine Compartment COUNTERSHAFT SPEED SENSOR TRANSMISSION CONTROL MODULE (TCM) TCS CONTROL UNIT ENGINE CONTROL MODULE (ECM) THROTTLE POSITION (TPI SENSOR ACCEL PEDAL SENSOR Attachments nsxd14047a (141 kB)

THRUST NEEDLE BEARING SEALING RINGS 35 mm 3RD GEAR NEEDLE BEARING 37 x 43 x 22 mm 2ND GEAR THRUST NEEDLE BEARING THRUST WASHER O-RINGS Replace. 2ND CLUTCH ASSEMBLY SPACER 31 mm LOCKNUT Replace. 140 N.m (14.0 kg-m. 101 Ib-ft) CONICAL SPRING WASHER Replace. SECONDARY SHAFT Check splines for excessive wear or damage. Check bearing […]

2ND CLUTCH ASSEMBLY FEELER GAUGE 2ND GEAR 3RD GEAR THRUST WASHER THRUST NEEDLE BEARING SECONDARY SHAFT/ 3RD GEAR Push this direction. THRUST NEEDLE BEARING NEEDLE BEARING 2ND GEAR THRUST NEEDLE BEARING THRUST WASHER 2ND CLUTCH ASSEMBLY CHAMFER 2ND CLUTCH ASSEMBLY SECONDARY SHAFT/ 3RD GEAR 2. Hold the 2nd clutch assembly against the 3rd gear. Measure […]

Unit of length: mm (in)SPRING SPECIFICATIONS ROLLER CAP LOCK-UP SHIFT VALVE LOCK-UP VALVE BODY LOCK-UP TIMING VALVE B Lock-up Valve Body Disassembly/Inspection/Reassembly Clean all parts thoroughly in solvent or carburetor cleaner, and dry with compressed air. Blow out all passages. Replace valve body as an assembly if any parts are worn or damaged. Check all […]

SPRING SPECIFICATIONS Unit of length: mm (in) REGULATOR VALVE BODY LOCK BOLT 6 x 1.0 mm 12 N.m (1.2 kg-m, 9 Ib-ft) REGULATOR VALVE COOLER RELIEF VALVE REGULATOR SPRING CAP VALVE SEAT LOCK-UP CONTROL VALVE SLEEVE CAP ROLLER Regulator Valve Body Disassembly/inspection/Reassembly— Clean all parts thoroughly in solvent or carburetor cleaner, and dry with compressed […]

Description The automatic transmission is a combination of a 3-element torque converter and a triple-shaft electronically controlled automatic transmission which provides 4 speeds forward and 1 in reverse. The entire unit is positioned in line with the engine. TORQUE CONVERTER, GEARS AND CLUTCHES The torque converter consists of a pump, turbine and stator, assembled in […]

Toward spring. Toward outside of valve body. Toward spring. Toward outside of valve body. Toward spring. Caps with flat ends and a groove around the cap are installed with the groove side opposite the spring. Toward spring. Caps with one projected tip and hollow end are in- stalled with the tip toward the spring. The […]

3RD ORIFICE CONTROL VALVE VALVE CAP ROLLER VALVE SEAT 2ND EXHAUST VALVE CPC VALVE SECONDARY VALVE BODY 4-3 KICK-DOWN VALVE CHECK BALLS (7/32) 7 3-2 KICK-DOWN VALVE FILTER Replace. Install in this direction. 4TH EXHAUST VALVE SERVO CONTROL VALVE MODULATOR VALVE 2ND ORIFICE CONTROL VALVE Secondary Valve Body Disassembly/lnspection/Reassembly Clean all parts thoroughly in solvent […]

Reverse Idler Gear Installation 1. Install the reverse idler gear. REVERSE IDLER GEAR 2. Set the spring in the reverse idler shaft. Push the spring in with the steel ball then install the needle bearing. NOTE: The steel ball is under spring pressure. Take care not to let it pop out. 3. Install the reverse […]

Shift Control Solenoid Valve A/B Test NOTE: Shift control solenoid valves A and B must be re- moved/replaced as an assembly. 1. Disconnect the connector from the shift control sole- noid valve A/B. 2. Measure the resistance between the No. 1 terminal (solenoid valve A) of the shift control solenoid valve connector and body ground […]