Category: Engine Lubrication

Engine Oil Inspection 1. Check engine oil with the engine off and the car parked on level ground. 2. Make certain that the oil level indicated on the dipstick is between the upper and lower marks. 3. If the level has dropped close to the lower mark, add oil until it reaches the upper mark. […]

Oil Level Engine Oil Inspection Replacement 1. Check engine oil with the engine off and the car parked on level ground. 2. Make certain that the oil level indicated on the dipstick is between the upper and lower marks. 3. If the level has dropped close to the lower mark, add oil until it reaches […]

Special Tools 8-9 8-5 Special Tools Mam Menu Table of Contents 1 Ref. No. Tool Number ‘ Description my Page Reference ≓ ↽ ⇠ ⋈ „ ↽ fl ↟ ↜⋡ ↽↽ ‚ (1) O7GAD—PH70201 он Seal Driver 1 ‘ 8-9 (Í) 07912 — 6110001 Oil Filter Wrench 1 8-5 8-2 Attachments nsxb08002a (28 kB)

Oil Pump Overhaul NOTE: • Use new O-rings when reassembling. • Apply oil to O-rings before installation. 6 x 1.0 mm 6 N-m (0.6 kg-m. 4 Ib-ft) PUMP COVER Inspection, page 8-8, 8-9 PUMP HOUSING Inspection, page 8-8, 8-9 OIL SEAL Installation, page 8-9 Replace. OUTER ROTOR Inspection, page 8-8, 8-9 SEALING BOLT 18 mm […]

Engine Oil Inspection 1. Check engine oil with the engine off and the car parked on level ground. 2. Make certain that the oil level indicated on the dipstick is between the upper and lower marks. 3. If the level has dropped close to the lower mark, add oil until it reaches the upper mark. […]

Engine Lubrication Illustrated Index FRONT CYLINDER HEAD ENGINE OIL PRESSURE GAUGE SENDING UNIT 22 N-m (2.2 kg-m. 16 Ib-ft) NOTE: • Use new O-rings when reassembling. • Apply oil to O-rings before installation. • Use liquid gasket, Part No. 08718-0001. • If the bottom of the oil pan is deformed, it should be repaired or […]

Oil Cooler, Oil Filter Base Illustrated Index NOTE: • Use new O-rings when reassembling. • Apply oil to O-rings before installation. • Use liquid gasket, Part No. 08718-0001. OIL COOLER CENTER BOLT 50 N-m (5.0 kg-m. 36 Ib-ft) 2 mm PIN O-RING Replace SPECIAL BOLTS 8 x 1.25 mm 22 N-m (2.2 kg-m, 16 Ib-ft) […]

Oil Filter Replacement CAUTION: Loosen the oil filter carefully while the engine is hot, the hot oil may cause scalding. 1. Remove the oil filter with the special tool as shown. 2. Inspect the threads and rubber seal on the new filter. Wipe off the seat on oil filter base, then apply a light coat […]

Oil Pressure Testing If the oil pressure warning light stays on with the engine running, check the engine oil level. If the oil level is correct: 1. Remove the engine oil pressure switch, and install an oil pressure gauge. 2. Start the engine. Shut it off immediately if the gauge registers no oil pressure. Repair […]

Engine Oil Replacement CAUTION: Remove the drain plug carefully while the en- gine is hot, the hot oil may cause scalding. 1. Warm up the engine. 2. Drain the engine oil. WASHER Replace. DRAIN PLUG 45 IM-m (4.5 kg-m, 33 Ib-ft) 3. Reinstall the drain plug with a new washer, and refill with the recommended […]