Seat Belts
Child Seat Anchor Plate
An attachment point is provided for a child restraint
system which uses a top tether. The tether bracket and
bolt are available at your Acura dealer. The tether at-
tachment point is located on the panel behind the
passenger’s seat-back.
1. Adjust the passenger seat fully forward to make
room behind the seat-back.
2. Using the dimensions shown, measure and mark
the location of the attachment point on the interior
panel.
3. Use a razor blade or sharp knife to carefully cut a 1
inch diameter circle at the point you marked. Cut
through one layer at a time. You will need to
remove two layers to reach the tether attachment.
4. Install the tether bracket and bolt and tighten to:
16 Ib-ft (22 N-m)
Make sure to route the tether through the space be-
tween the headrest and seat.
8 x 1.25 mm
22 N-m (2.2 kg-m, 16 Ib-ft)
25 mm
(1 in)
CHILD SEAT
ANCHOR PLATE
100 mm
(25.4 in)
246 mm
(62.5 in)
NOTE:
• Do not remove the toothed washer from the
child seat anchor plate. Use the child seat an-
chor plate with the toothed washer attached to
it.
• When installing a child seat, follow the instruc-
tions of the manufacturer of the child seat.
• Additional anchor plates are available.
Do not use the anchor plate for any
other purpose; it is designed exclusively for in-
stallation of a child seat.
Rearview Mirror
Replacement
1. Carefully remove the cover with a flat tip
screwdriver.
2. Loosen the lock bolt, then slide the mirror stay from
the lug.
MIRROR
LUG
MIRROR STAY
LOCK BOLT
Counter-
clockwise
COVER
3. Remove the lock bolt, then remove the toothed
lock washer and hold spring from the mirror stay.
LOCK BOLT
Left-hand threads
TOOTHED LOCK WASHER
HOLD SPRING
MIRROR STAY
4. Installation is the reverse of the removal procedure.
Child Seat Anchor Plate
An attachment point is provided for a child restraint
system which uses a top tether. The tether bracket and
bolt are available at your Acura dealer. The tether at-
tachment point is located on the panel behind the
passenger’s seat-back.
1. Adjust the passenger seat fully forward to make
room behind the seat-back.
2. Using the dimensions shown, measure and mark
the location of the attachment point on the interior
panel.
3. Use a razor blade or sharp knife to carefully cut a 1
inch diameter circle at the point you marked. Cut
through one layer at a time. You will need to
remove two layers to reach the tether attachment.
4. Install the tether bracket and bolt and tighten to:
16 Ib-ft (22 N-m)
Make sure to route the tether through the space be-
tween the headrest and seat.
8 x 1.25 mm
22 N-m (2.2 kg-m, 16 Ib-ft)
25 mm
(1 in)
CHILD SEAT
ANCHOR PLATE
100 mm
(25.4 in)
246 mm
(62.5 in)
NOTE:
• Do not remove the toothed washer from the
child seat anchor plate. Use the child seat an-
chor plate with the toothed washer attached to
it.
• When installing a child seat, follow the instruc-
tions of the manufacturer of the child seat.
• Additional anchor plates are available.
Do not use the anchor plate for any
other purpose; it is designed exclusively for in-
stallation of a child seat.
Rearview Mirror
Replacement
1. Carefully remove the cover with a flat tip
screwdriver.
2. Loosen the lock bolt, then slide the mirror stay from
the lug.
MIRROR
LUG
MIRROR STAY
LOCK BOLT
Counter-
clockwise
COVER
3. Remove the lock bolt, then remove the toothed
lock washer and hold spring from the mirror stay.
LOCK BOLT
Left-hand threads
TOOTHED LOCK WASHER
HOLD SPRING
MIRROR STAY
4. Installation is the reverse of the removal procedure.