Seat Belts
Replacement
SRS wire harnesses are routed near the retractor.
All SRS wire harnesses and connec-
tors are colored yellow. Do not use electrical test
equipment on these circuits.
CAUTION:
Be careful) not to damage the SRS wire
harnesses when servicing the retractor.
Remove the short connector (RED) from the its
holder and disconnect the SRS wire harness
connector, then connect the short connector
(RED) to the tensioner connector.
NOTE: To prevent dust, wrap the SRS wire
harness connector with a protective cover.
RETRACTOR
SEAT BELT
TENSIONER
PROTECTIVE
COVER
SRS WIRE
HARNESS
SRS WIRE HARNESS
CONNECTOR
TENSIONER
CONNECTOR
CONNECTOR
HOLDER
SHORT
CONNECTOR
(RED)
CAUTION: Check the seat belts for damage, and replace them if necessary. Be careful not to damage them during
removal and installation.
1. Remove:
Seat (see page 20-39(’93-’96), 38)
Center pillar trim panel (see page 20-38)
2. Remove the three anchor bolts, retractor bolt and retractor mounting bolt, then remove the seat belt and seat belt
buckle.
CAUTION: When removing the retractor, do not touch the seat belt tensioner.
NOTE: When removing the anchor bolts and retractor bolt, use a 17 mm socket or box-end wrench.
RETRACTOR MOUNTING
BOLT
6 x 1.0 mm
13 N·m (1.3kg-m, 9 Ib-ft)
* UPPER ANCHOR BOLT
7/16-20 UNF
33 N·m (3.3 kg-m.
24 Ib-ft)
CENTER PILLAR TRIM
PANEL
(see page 20-38)
SEAT BELT
TENSIONER
RETRACTOR BOLT
7/16-20 UNF
33 N·m (3.3 kg-m, 24 Ib-ft)
* CENTER ANCHOR BOLT
7/16-20 UNF
33 N·m (3.3 kg-m, 24 Ib-ft)
CENTER PILLAR
TRIM PANEL
PROTECTIVE
BAG
SEAT BELT BUCKLE
SEAT BELT
CAP
* LOWER ANCHOR BOLT
7/16-20 UNF
33 N·m (3.3 kg-m, 24 Ib-ft)
(cont’d)
Disconnect the connector (driver’s only).
RETRACTOR
Replacement
SRS wire harnesses are routed near the retractor.
All SRS wire harnesses and connec-
tors are colored yellow. Do not use electrical test
equipment on these circuits.
CAUTION:
Be careful) not to damage the SRS wire
harnesses when servicing the retractor.
Remove the short connector (RED) from the its
holder and disconnect the SRS wire harness
connector, then connect the short connector
(RED) to the tensioner connector.
NOTE: To prevent dust, wrap the SRS wire
harness connector with a protective cover.
RETRACTOR
SEAT BELT
TENSIONER
PROTECTIVE
COVER
SRS WIRE
HARNESS
SRS WIRE HARNESS
CONNECTOR
TENSIONER
CONNECTOR
CONNECTOR
HOLDER
SHORT
CONNECTOR
(RED)
CAUTION: Check the seat belts for damage, and replace them if necessary. Be careful not to damage them during
removal and installation.
1. Remove:
Seat (see page 20-39(’93-’96), 38)
Center pillar trim panel (see page 20-38)
2. Remove the three anchor bolts, retractor bolt and retractor mounting bolt, then remove the seat belt and seat belt
buckle.
CAUTION: When removing the retractor, do not touch the seat belt tensioner.
NOTE: When removing the anchor bolts and retractor bolt, use a 17 mm socket or box-end wrench.
RETRACTOR MOUNTING
BOLT
6 x 1.0 mm
13 N·m (1.3kg-m, 9 Ib-ft)
* UPPER ANCHOR BOLT
7/16-20 UNF
33 N·m (3.3 kg-m.
24 Ib-ft)
CENTER PILLAR TRIM
PANEL
(see page 20-38)
SEAT BELT
TENSIONER
RETRACTOR BOLT
7/16-20 UNF
33 N·m (3.3 kg-m, 24 Ib-ft)
* CENTER ANCHOR BOLT
7/16-20 UNF
33 N·m (3.3 kg-m, 24 Ib-ft)
CENTER PILLAR
TRIM PANEL
PROTECTIVE
BAG
SEAT BELT BUCKLE
SEAT BELT
CAP
* LOWER ANCHOR BOLT
7/16-20 UNF
33 N·m (3.3 kg-m, 24 Ib-ft)
(cont’d)
Disconnect the connector (driver’s only).
RETRACTOR
Seat Belts
Replacement (cont’d)
Anchor bolt construction:
TOOTHED
LOCK WASHER
PLAIN
WASHER
* UPPER ANCHOR BOLT
BEARING
TOOTHED
LOCK WASHER
SPRING WASHER
* CENTER ANCHOR BOLT
3. Check that the retractor locking mechanism functions as described on page 20-45(’93-’96) (’91-’92).
4. Installation is the reverse of the removal procedure.
NOTE:
Make sure you assemble the washers on the anchor bolts as shown.
Before attaching the center pillar trim panel, make sure there are no twists or kinks in the seat belts.
On reassembly, replace the anchor bolts (*) and use liquid thread lock.
SPRING WASHER
RETRACTOR BOLT
* LOWER ANCHOR BOLT
TOOTHED
LOCK WASHER
SPRING WASHER