NOTE:
• Use only genuine Honda wheel weights for aluminum wheels. Non-genuine wheel weights may corrode and damage
the aluminum wheels.
• On the aluminum wheels, remove the center cap from inside of the wheel after removing the wheel.
• Before installing the brake disc, clean the mating surface of the rear hub and inside of the brake disc.
• Before installing the wheel, clean the mating surfaces of the brake disc and inside of the wheel.
Corrosion resistant bolt/nut
FLANGE BOLT
10 x 1.25 mm
65 N-m (6.5 kg-m,
47 Ib-ft)
KNUCKLE
SPLASH GUARD
HUB BEARING
ASSEMBLY
Inspect for faulty
movement and wear.
Replacement, page 18-33
WHEEL NUT
12 x 1.5 mm
110 N-m (11 kg-m,
80 Ib-ft)
REAR HUB UNIT
Check for damage and
cracks.
Replacement, page 18-33
BRAKE DISC
Check for wear and
rust.
Inspection,
Section 19.
FLAT HEAD SCREW
6 x 1.0 mm
10 N-m (1.0 kg-m,
7 Ib-ft) CENTER CAP
Rear Suspension
Hub Replacement
1. Remove the center cap, then pry the spindle nut
lock tab away from the spindle and loosen the nut.
2. Raise the car, and support it with safety stands (see
Section 1).
WHEEL NUT
110 N-m
(11 kg-m, 80 Ib-ft)
SPINDLE NUT
26 x 1.5 mm
Replace.
NOTE: After tightening, use a drift
to stake spindle nut shoulder
against the driveshaft.
3. Remove the rear wheels.
NOTE: Before installing the wheel, clean the
mating surfaces of the brake disc and inside of the
wheel.
4. Remove the spindle nut.
5. Remove the wheel sensor from the knuckle and the
rear of the lower control arm, then secure the wheel
sensor wire to the suspension arm.
NOTE:
• Do not disconnect the wheel sensor.
• Be careful when installing the sensors to avoid
twisting wires.
22 N-m
(2.2 kg-m,
16 Ib-ft)
WHEEL SENSOR
Corrosion resistant bolt/nut
10 N-m
(1.0 kg-m, 7 Ib-ft)
6. Remove the banjo bolt and disconnect the brake
hose, then remove the brake hose clamp from the
knuckle.
CAUTION: Avoid spilling brake fluid on painted,
plastic or rubber surfaces as it can damage the
finish; wash spilled brake fluid off immediately with
clean water.
BANJO BOLT
35 N-m (3.5 kg-m, 25 Ib-ft)
BRAKE HOSE
WASHER
Replace.
BOLT 6 mm
10 N-m (1.0 kg-m, 7 Ib-ft)
Corrosion resistant bolt/nut
7. Remove the rear caliper by removing the mounting
bolts.
CALIPER BRACKET MOUNTING BOLT
110 N-m (11 kg-m, 80 Ib-ft)
CALIPER ASSEMBLY
Corrosion resistant bolt/nut
8. Remove the flat head screws.
Screw two 8 x 12 mm bolts into the disc to push it
away from the hub.
NOTE: Turn each bolt two turns at a time to pre-
vent cocking the disc excessively.
FLAT HEAD SCREW
6 x 1.0 mm
10 N-m (1.0 kg-m, 7 Ib-ft)
BRAKE DISC
9. Remove the rear hub unit from the knuckle.
FLANGE BOLT
10 x 1.25 mm
65 N-m (6.5 kg-m, 47 Ib-ft)
8 x 12 mm
BOLT
REAR HUB UNIT
Corrosion resistant bolt/nut
Rear Wheel Bearing Replacement:
1. Separate the wheel bearing from the hub using the
special tools and a press.
CAUTION: Hold onto the hub to keep it from fall-
ing when pressed clear.
Press
HUB DIS/ASSEMBLY
BASE
07GAF-SD40700
HUB DIS/ASSEMBLY PIN
07GAF-SD40100
WHEEL BEARING
Replace.
HUB
2. Remove the wheel bearing inner race from the hub
as shown.
Press
HUB DIS/ASSEMBLY PIN
07GAF-SD40100
INNER RACE
Replace.
BEARING
SEPARATOR
0-41/2 in.
(Commercially
available)
NOTE: Wash the bearing and hub thoroughly in
high flash point solvent before reassembly.
Rear Suspension
Hub Replacement
NOTE: Replace the bearing with a new one after
removal.
3. Press a new wheel bearing onto the hub using the
special tools and a press.
Press HUB ASSEMBLY
DRIVER ATTACHMENT
07GAF-SD40200
WHEEL BEARING
HUB DIS/ASSEMBLY PIN
07GAF-SD40100
SUPPORT BASE
07965-SD90100
4. Install the hub in reverse order of removal.